@baztom On eWAN settings Enable the IPv4 then expand the Advanced settings and look for Use the Following DNS Addresses Checkout the screenshot         ... View more

@5872615 If you have TP-Link Vr1600v go to Advance Tab -> Wirless -> Advance Settings Then tick enable WPS Here's a sceen shot           ... View more

@flyfisho There shouldn't be any issue with thoes ports. Try to factory reset the modem and reconfigure those ports after. ... View more

Most Mode/Router put a sticker on the modem it self where you can see the SSID and WLAN Key. BTW. You will get your own router. Be patient.   ... View more

@brmoss Quick question. Is your ADSL still working? If you'r ADSL still works it means that your house is still connected to the ADSL infrastructure. An NBN Technician is needed to disconnect your house from the old ADSL infrastructure and connect it to the NBN Distribution Point Unit out side your house. After that you can do all the end user equipment installation like the NBN NCD and the ISP provided Router.   ... View more

@Steve68 The settings is stpot on. So if it's not the settings it could be something else. What's the error message you get when you try to send an email? ... View more

@Steve68 What email client are you using? Can you please post the SMTP settings? ... View more

@BobbyDigital   WDS on TP-Link VR1600v can use WPA/WPA2   ... View more

@Pierre For TPG FTTH go to Advance Tab -> Network -> eWAN VLANID should be enabled use VLANID: 2 Internet Connetion Type: PPPoE     Also you'll replace a Netcomm NF7 Which means you will also used this router for NBN FTTP Here's the settings for NBN FTTP For NBN FTTP go to Advance Tab -> Network -> eWAN VLANID should be DISABLED Internet Connetion Type: PPPoE ... View more

there should be a time settings under system tools on advance tab ... View more

I  don't know and there's now way for me find out, but you should get the equipment before the service gets installed. ... View more

If you order the service on the 25th which is Friday and TPG uses Startrack. There could be some delay on the shipping due to long weekend because of the Holiday. But it still nice to get an answer from an admin. ... View more

the internet light is the internet settings of the modem. some modem's internet light goes off if no one is using the internet. what kind of modem are you using and do you have NBN or ADSL2+? ... View more

Tha's an anusual result. Your Upload is faster than the Download. Did you run this on Wifi or Ethernet? What kind of NBN internet do you have and also the router that your're using? ... View more

the issue seems to be the wifi connectiong between the router and the PS4 What router are you using?   ... View more

@BobbyDigital orbistat is right on the spot. If you insist on a wifi bridge VR1600 have a WDS feature however NB604n does not.. You get another modem with WDS feature or another VR1600 and use WDS to connect the two vr1600 wirelessly. so basically you will have this   Internet ---> VR1600V ---> wireless bridge "WDS" ---> VR1600V --- ethernet --> CCTV   I can't emphasize enough that it will not be as reliable as an Ethernet connection... ... View more

@moon what's the error message that you get when you try your iphone?   ... View more

@Red33 It's very unlikely that the modem or the cable got damage when you unplug it. Well let's start with your modem. What's your modem and what kind of internet do you have "adsl or NBN"? And also which light on the modem are on and solid? ... View more

@Mazito62 This normally happen when you port your number from telstra. did you port your number from telstra? ... View more

@bluey1423 It's very unlikely that the switch to NBN have caused the issue and singled out one of you P.C. Have you tried to check your upload on Safe mode with networking? ... View more

@MacMag You can configure the VR900 as a wireless router / wireless access point together with the TPG suplied equipment It should be easy and simple   ... View more

@craig210788 I've seen some people did this but not sure if it's for D700 as well but the idea is if it's for HFC you have to set your Netgear as a wireless/home gateway to enable the WAN/Internet Port instead of the ADSL/VDSL port. For some netgear it should be on advance tab -> set up -> XDSL then go to internet settings and enable VLAN tagging and set it to 2 use PPPoE for the connection type and enter your TPG UN and PW     ... View more

@bluey1423 have you tried system restore? If you can remember the last time your P.C work as normal and restore it to that date or prior to it.   ... View more

  Or can I use our own to replace it? Can someone from TPG answer these?   you may use your own router just make sure that it's an NBN HFC supported router and your HP will not work. they do have a new equipment for NBN. If you have HFC they have a TP-Link VR1600.     ... View more

@victor41 I checked netgear webpage and they actually have a video on how to set it up. here's the link if you havent seen it yet. https://www.netgear.com/support/product/RBK50.aspx#ConfigurationAssistance_CommonTopics   ... View more

Yes could be firmware. what is the firmware of your modem?   ... View more

@Terminator312 I use to do this at home because my kids watch too much youtube and netflix.   There should be a bandwidth control under Internet Tab you may want to configure the IP reservation as well should you wish to properly control on how much bandwidth each device can use ... View more

@philgaudet   If you have NBN look for NBN Home Phone Services after you log in instead. After you Log in to my account go to NBN Home Phone Service, then Home phone service control and you should see the call divert on that page.       ... View more

 @bluey1423 okay now more curious. hmmm.......   Have you installed any software or update anything on your computer when you got NBN? If hardware is not the issue it could be a software. However base on what you said the issue started when you swithed to NBN..   One thing that will change for sure when you switch to NBN is your gateway. Some gateway have bandwidth/traffic control. You should check your gateway if this feature is enable. What modem/router are you using?   If you have TP-Link VR1600 bandwidht control is under advance tab Check if this feature is enable and what I.P is being control and how much is the Up (min/max)   ... View more