TPG Community

Get online support
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
Ask a Question

About amcam

since ‎28-08-2022
‎04-09-2022
amcam
Level 2

Re: TPG NBN VR1600 - Orbi - Port Forwarding

by Level 2 in NBN Installation
‎01-09-2022 10:17 PM
‎01-09-2022 10:17 PM
Thanks for all your help David. After several more attempts, I still couldn't get a network connection in AP mode.  However in router mode I noticed I had my VR1600 port forward set to the server rather than the Orbi.  I changed it and my port is now open! ... View more

Re: TPG NBN VR1600 - Orbi - Port Forwarding

by Level 2 in NBN Installation
‎30-08-2022 03:07 PM
‎30-08-2022 03:07 PM
Thank you for your kind reply David.   Under "Advanced", the Orbi shows "Router information" IP address  10.0.0.1 IP subnet mask  255.255.255.0   Under "Internet port" it shows: IP address 192.168.1.104 IP subnet mask  255.255.255.0 Domain name server  192.168.1.1    0.0.0.0   Yes I tried AP mode .. twice.  I lost my internet connection and couldn't get it back, no matter what I tried.  See attached file.  I put things back as the were.  How do I " any internet sessions via the Orbi may have to be re-established." ?   Next steps please.   ... View more

Re: TPG NBN VR1600 - Orbi - Port Forwarding

by Level 2 in NBN Installation
‎30-08-2022 02:24 PM
‎30-08-2022 02:24 PM
Current my Orbi network is on 10.0.0.xxx.   I've tried to change the address to match the tplink router, 198.168.1.xxx  as you suggested, at ADVANCED>Setup> LAN Setup    .  However I get the message:    "IP address is conflicted with WAN IP subnet, please enter again."   I've played around but I have no idea how to fix this. Help please! ... View more

Re: TPG NBN VR1600 - Orbi - Port Forwarding

by Level 2 in NBN Installation
‎29-08-2022 11:13 AM
‎29-08-2022 11:13 AM
Thank you for your reply.   My security cameras are connected to the Orbi network, and Sighthound has to be on the server on the same network.   The VR1600 has a dynamic IP from TPG.  I've set the Orbi network cameras and server static.   1. I did actually try the AP mod on the Orbi but immediately lost my network connection.  I was going to try it again today. 2.  I don't understand this.  How do I set the IP of the Orbi?  I have wired connections between VR1600 and Orbi and server.   It's an RBS50.   Port 8848       ... View more

Re: TPG NBN VR1600 - Orbi - Port Forwarding

by Level 2 in NBN Installation
‎28-08-2022 09:27 PM
‎28-08-2022 09:27 PM
DHCP is enabled. The security system (Sighthound) is software running on the server.  Wifi on the VR1600 is turned off.  I'm using the Orbi for wifi. No.  The security system is using Orbi addresses 10.0.0.xx The phone has a special Sighthound app. Thanks for your help.  What next?  Turn off DHCP? Should I also have AP mode set?  Will this affect my phone ? ... View more

TPG NBN VR1600 - Orbi - Port Forwarding

by Level 2 in NBN Installation
‎28-08-2022 10:07 AM
‎28-08-2022 10:07 AM
I have TPG NBN with a TPG VR1600v.  I have the VR1600 connected to an Orbi system because we have a 3 story house with poor signal.  I have TPG voip phone service.  It is working well.   I have a security system that I need to access via my mobile phone.  Previously it was working fine but I can't get it working through the VR1600 - Orbi.  I have set port forwarding on both the VR1600 and the Orbi using TCP/UDP.  A port check shows UDP open but TCP remains subbornly closed.  My security system uses TCP.  I hence can't get a connection to my security system from my phone.   I have read that bridging on the VR1600 will not allow the phone to work.   Please help. ... View more
Latest Tags
No tags yet