TPG Community

Get online support
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
Ask a Question

Archer vr1600v bridge mode - Totally confused.

chrisgrind
Level 2
Level 2
‎27-02-2022 08:52 AM

thanks. I must have a faulty device, I've done this countless times trying to get it working, with mutiple devices behind it (pfsense, openWRT), and none of them will pick up an IP on the WAN port via the bridged vr1600v

0 Likes
Reply
david64
Master
Master
‎27-02-2022 09:16 AM

@chrisgrind . Factory reset Archer, put in your details, and connect to the phone socket.

If DSL light stays off, it could be a blown DSL port or there is a line fault.

Check the Archer system log. If there are PPP messages, the router is not receiving frames from the phone line.

0 Likes
Reply
orbistat
Level 8
Level 8
‎27-02-2022 12:52 PM
@chrisgrind wrote:

thanks. I must have a faulty device, I've done this countless times trying to get it working, with mutiple devices behind it (pfsense, openWRT), and none of them will pick up an IP on the WAN port via the bridged vr1600v

Once the VR1600v is bridged it's simply a modem, you'll lose connectivity to it's web management page. The VLAN 2 Id needs to be set in the WAN interface of the now seperate router as you're not using the VR1600v for routing.

 

You're external router's WAN port should be connected to a LAN port on the VR1600v (not it's WAN port) set up a PPPoE connection with just TPG username and password and Vlan 2 enabled for that connection.

0 Likes
Reply
chrisgrind
Level 2
Level 2
‎27-02-2022 02:10 PM

 

@orbistat wrote:
@chrisgrind wrote:

thanks. I must have a faulty device, I've done this countless times trying to get it working, with mutiple devices behind it (pfsense, openWRT), and none of them will pick up an IP on the WAN port via the bridged vr1600v

Once the VR1600v is bridged it's simply a modem, you'll lose connectivity to it's web management page. The VLAN 2 Id needs to be set in the WAN interface of the now seperate router as you're not using the VR1600v for routing.

 

You're external router's WAN port should be connected to a LAN port on the VR1600v (not it's WAN port) set up a PPPoE connection with just TPG username and password and Vlan 2 enabled for that connection.

thanks, this is what I have tried to do. Just having no luck with it. When i reference the WAN port, I meant on pfsense/openWRT

 

I've got a dual NIC computer with PFsense running. Also tried an old modem/router and did a custom firmware with openWRT and it won't pick up an IP address either.

 

 

 

0 Likes
Reply
chrisgrind
Level 2
Level 2
‎27-02-2022 02:11 PM
@david64 wrote:

@chrisgrind . Factory reset Archer, put in your details, and connect to the phone socket.

If DSL light stays off, it could be a blown DSL port or there is a line fault.

Check the Archer system log. If there are PPP messages, the router is not receiving frames from the phone line.

thanks. The archer works ok when connected as a modem/router, but as soon as it goes to bridge mode, it appears to not pass data. This is with vlan 2 set.

0 Likes
Reply
david64
Master
Master
‎27-02-2022 02:30 PM

@chrisgrind . Are all the Archer lan ports working?

You mention an old modem/router. With Archer in bridge mode (with vlan id), can you connect the old router running in standard mode (no vlan id) to the Archer and get internet connection?

Do you have packet capture software (eg. Wireshark) on your computer? See if Archer is sending frames on its lan ports.

0 Likes
Reply