TPG Community

Get online support

HFC and Google Wifi

SOLVED Go to solution
Highlighted
Level 2

Hi folks,

 

I have the NBN with TPG, over HFC. Bought Google Wifi to sort the wifi in my long skinny house, but haven't been able to get it to get an internet connection.

 

So, existing setup was the standard TPG supplied Arris NBN modem -> Huawei HG659 router.

 

Having done a bit of research it seems some people have been able to connect Google Wifi direct to their HFC modem i.e. Arris NBN modem -> first Google Wifi point. I tried this first but it tells me it can't get an internet connection.

 

I then tried connecting the first Google Wifi point directly to the HG659 i.e. Arris NBN modem -> HG659 -> first Google Wifi point. Same result.

 

I've also tried entering my TPG account and password into the PPPoE settings of the Google Wifi, but same result. Done multiple restarts of everything etc.

 

I found the article on putting the HG659 in bridge mode and will try that next, although that seems to only be required if you want to use the HG659 for VOIP which I don't need. Ideally I would get rid of the HG659 altogether.

 

Can anyone point me in the right direction? Does anyone have Google Wifi connected directly to their Arris NBN modem with HFC?

 

Thanks ...

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Moderator

Good day @Wilbur.

 

Welcome to TPG Community!

 

If you wish to use a third party modem/router for your NBN HFC technology. It should be a VDSL modem since you are going to set the VLAN ID to 2.

 

I believe your Google WiFi is just a router which is not compatible for the NBN HFC configuration (Can't replace the Huawei modem/router).

 

You may check this community discussion with one of our customer who used a different VDSL2 modem (ASUS). https://community.tpg.com.au/t5/Broadband-Internet/Alternate-router-to-use-on-HFC/m-p/863#M2149

 

Regards,

View solution in original post

11 REPLIES 11
Highlighted
Moderator

Good day @Wilbur.

 

Welcome to TPG Community!

 

If you wish to use a third party modem/router for your NBN HFC technology. It should be a VDSL modem since you are going to set the VLAN ID to 2.

 

I believe your Google WiFi is just a router which is not compatible for the NBN HFC configuration (Can't replace the Huawei modem/router).

 

You may check this community discussion with one of our customer who used a different VDSL2 modem (ASUS). https://community.tpg.com.au/t5/Broadband-Internet/Alternate-router-to-use-on-HFC/m-p/863#M2149

 

Regards,

View solution in original post

Highlighted
Level 2

Thanks for the info. I've put the Huawei into bridged mode, and everything is now working, but yes as you've said the Huawei modem/router is still required.

 

So for anyone using this in the future the working setup is:

Arris NBN modem -> HG659 in bridged mode -> first Google Wifi point.

 

Thanks for the assistance.

Highlighted
Moderator

You're welcome, @Wilbur.

 

Should you require further assistance, feel free to drop us a message. Cheers!

Highlighted
Level 2

Hi,

I’ve just read an interesting post and answer re HFC and Google WiFi set up.  On a related point, am I able to connect my Google WiFi behind a Netgear R7000P router (instead of the supplied Huawei HG659) and have voice calls as part of a new TPG connection?

Thanks.

 

Highlighted
Level 8

Hi @mgw2 The simple answer is no, you need to use the supplied HG659 modem/router to keep the included VOIP service. Even if you were to obtain and enter the settings into your Netgear R7000P the server would not authenticate it.

Highlighted
Level 2

Thanks @orbistat for the quick reply. 

 

So if I stick with the HG659 and set up my Google WiFi behind that (in bridge mode), does that mean the phone function will be disabled?  If so, is there a way I can have Google WiFi and a phone connection available?

 

Cheers.

Highlighted
Level 8

Hi @mgw2 If you set the HG659 to bridge mode it has no way of routing the VOIP so yes you'll lose your phone, I'm not familiar with the interface on the Google WiFi or whether you can change it from router mode to access point mode.

Depending on that you might be able to switch off DHCP and WiFi on the HG659 and let the Google WiFi do all the routing, although I just had a quick look at a HG659 and can't see an option to disable NAT separately. Further testing required.

Highlighted
Level 1a

Hi Wilbur

 

I am attempting the same thing but with a couple of differences

  1. I had setup the mesh having shut down the IInet router DCHP and wifi.
  2. The iinet router is a Technicolor TG789vac V2

and I have been running like that for several months and now have an extensive IoT setup off this.

 

Unfortunately, I have not able to forward ports under this setup and wanted to do exactly what you did, without loosing the whole IoT setup by resetting google account!

 

I bridged the router but I couldn't get primary router in the mesh to connect to internet. I suspect I it might work if I reset the google router - but then, I may end up having to do quite a bit of setting up again! 

 

My question is, did you ever get the network working before you bridged the iitnet router? If so, did you have to reset the primary router and loose all the google setup when you bridged the iinet router.

 

Your assistance is much appreciated.

Highlighted
Level 3

FYI for the TP-Link Archer 1600V I have successfully setup the Google Wifi.

 

In the router settings:

Advanced > Network > DSL > Add...

 

Modulation Type: VDSL

VLAN ID: Disabled

Internet Connection Type: Bridge

 

The bridge was then displayed on the Network > Interface Grouping as LAN1 port. I connected the Google WiFI to the LAN1 port on the Archer router and continued to successfuly setup the Google Wifi via the Google Home app. I then disabled the WiFi radio no the Archer modem and all is working peachy (and MUCH faster than the Archer!)