TPG Community

Get online support

Deco x20 connection to NBN HFC

DavePhillips
Level 2
I have searched the support but the links don’t seem to work.

Network is up and running well now with NBN HFC box and TPG router/WiFi- both network cables and WiFi network.

I have a new TP Link Deco X20 Mesh set which I want to use to boost reception throughout the house.

The set-up for this has failed once I try to connect to the network. My questions are:

1. Should the X20 be connected to the NBN HFC box or the TPG router/WiFi unit.

2. The set up requires information on connection type. Default is dynamic IP. If this is not the case please advise which connection type I should use and the necessary details.

Many thanks for your help with this.

Dave
7 REPLIES 7
david64
Master

Hi Dave.

1. If you want to use the VOIP phone service bundled with TPG, the TPG router has to connect to the NBN box. If you don't want to use the VOIP service, you have a choice of which to connect to the NBN box. If you connect the Deco to the NBN box, its wifi might be sufficient to not use the TPG router.

2. To use the Deco in place of TPG router, the connection type is PPPoE which requires your username with @TPG.com.au and your password (not the Community ones). In Advanced Features, Enable VLAN mode, Internet VLAN ID=2, priority=0. You can compare the settings between TPG router and Deco.

If you need the VOIP service, the Deco setup is different. There are several posts about connecting a second router and I'm not clear on what works.

DavePhillips
Level 2
Thankyou so much - I tried the PPPoE last night before the reply without the VLAN info so I’ll give that a go today.
We don’t need the VOIP so hopefully you guidance will get us on-line. I’ll revert with the result once I’ve tried.
DavePhillips
Level 2
Brilliant - the advice worked and I know have all 3 Deco x20 units providing strong WiFi signal with 100mb/s throughout the house.

The key part of the advice was TPG user name with “ @TPG.com.au “ at the end. I entered the VLan info in the set-up but left the IPTV settings blank.

Also one tip - if the set-up fails (red light) then use the reset button on the X20 device to get back to the installation beginning.

It took me about 6 attempts but once I had the right data from TPG community support it worked first time 😀
Chrisholder
Level 2
I have recently bought the Deco x20 DSL as my main router. All fine up until I try and set up the WiFi and then I get the red light. Have checked with TP Link all seems right on their end, and same story with TPG. Used username@TPG.com.au along with all the above VLAN details but no luck. Really frustrating
BasilDV
Moderator

Hi @Chrisholder

 

We'd like to check on this further.

Kindly send us a PM with your TPG account details for further assistance.

 

BasilDV

awg
Level 2
Level 2

What's the use of a "community" forum if the Moderators just give the solutions outside of the thread? I'm now facing the same issue for a friend. The TP-Link X20-DSL model seems a great choice for people who are stuck on vDSL configurations, but we can't get this to work.

 

Stepping through the TP-Link wizard we've selected PPPoE, entered the username with the @TPG.com.au domain, confirmed the correct password, and set the VLAN ID to '2'. The device is still unable to connect to the Internet.

 

Notably, this is after an NBN technician has visited the site and stated the old router was dead, but the internet connection itself was "working with good signal". Can anyone lend any further insight into getting this up and running?

david64
Master

Hi @awg . Is this the Deco X20 DSL model?

For FTTB/FTTN connections, you have to set the Deco into DSL Modem Router Mode (step 4 in user guide).

Set DSL connection type as VDSL.

Phone cable goes to DSL port on main unit.

Regarding VLAN ID, are you sure it was used on the old router? You can try disabling it.