5112552

SOLVED Go to solution
jharitos75
Level 4

Hi,

 

I have received both NCD and modem and installed them yesterday - plugged in and still no internet light on Modem.

 

Its been more than 24hours, can someone please advise when I will be connected???

 

Thanks

1 ACCEPTED SOLUTION

Accepted Solutions
jharitos75
Level 4

Thanks Rajen,

 

I received a call from Tech Support and they have booked an NBN tech to visit me next Friday 24th.. Fingers crossed for a resolution.

 

Appreciate your help

View solution in original post

48 REPLIES 48
david64
Master

Are all lights lit on the NCD? What lights are lit on the wifi router?

Did you have ADSL before this NBN? Was ADSL still working before you connected the NBN?

 

jharitos75
Level 4

Hi David,

 

Power, 2.4GB 5GB WAN and LAN 1 are green lit on Modem but no Internet light.

 

Yes ADSL was still working but I disconnected old modem as per instructions from TPG.

 

New NCD unite received and plugged in and all blue liughts.

 

Can you help please mate?

 

 

david64
Master

Turn both boxes off. Turn NCD on and wait for 3 lights to go blue. Then turn on router. NCD 4th light should go blue. If no Internet light this time, logon to the router and check its config to make sure your TPG username and password are correct.

 

Do you have an Archer router? There's some info here:

How to set up your TP-Link VR1600v modem

jharitos75
Level 4

I have tried 3-4 times David and all I get from my NDC box is the first two blue lights... the third (DSL) flickers on an off for a little while then goes off completely.

 

Its is not the phone jack as I am currently connecting via TPG ADSL and a very old router but still working.

 

Is my NBN service configured, I never received an email or SMS to say I was connected, just the Router and NDC box yesterday morning.....

RajenS
Moderator

What is this guide all about?

 

This guide will help you set up your NBN Fibre to the Curb (FTTC) service from TPG.

 

Read on for our step-by-step instructions or check out our helpful youtube video:

 

 

 

 

 

Important Note: Once you receive confirmation from TPG that your NBN service  is active, turn on your router and leave it for up to 30 mins as your router is retrieving and saving the required settings from TPG to connect automatically. When this is completed, the internet light on the front of your router will become solid green.

 

Before you get started, you’ll need 3 things

 

1. A message from us advising you to plug in your NBN FTTC equipment:

 

 

 

 

FTTCSMS.png

 

 

2. Your TPG Modem:

tplink.png

 

Tip! Check your modem delivery status here 

 

3. An NBN Network Connection Device, or NCD for short:

ncd.png

 

You should also make sure there are 2 available electrical outlets near your telephone wall socket. If your home has been connected to the NBN before, there may already be an Network Connection Device plugged in at your premises. If not, a new Network Connection Device will be delivered to you along with your modem.

 

Connecting your equipment

 

First things first, make sure your Network Connection Device is plugged in correctly. 

 

 

 

FTTC1.png

 

 

1. Connect the supplied power cable from the Network Connection Device to your power point

2. Connect the supplied phone cable from the Network Connection Device straight into the phone socket on the wall.

 

Important! Do not use a line filter/splitter (from your old ADSL service) when plugging in the Network Connection Device. 

 

filter.png

 

 

Now it’s time to plug in your TPG modem

 

1. First, use the supplied Ethernet cable to connect your modem’s WAN port to the Gateway port on your Network Connection Device. (This is the blue cable in the diagram below marked with a 2)

 

Fttc2.png

 

2. Next, use the power cable to connect the Power port to an electrical outlet (marked with a 1 in the diagram)

 

3. Finally, make sure the electrical outlets for both devices are switched on, then allow 15 minutes for your modem to boot up and configure automatically.

 

The initial setup is now complete!

 

Check the lights on your Network Connection Device

 

Once you’re done with the above steps, check the lights on your Network Connection Device. If any lights are off or red, make sure that your cables are plugged in securely. You may need to plug your NCD into a different telephone wall socket if your home has more than one.

Once all the lights are blue or amber, you can start connecting your devices and get online.

 

Note: An amber LAN light should not prevent a successful connection, but you’ll need to call us if the Connection light is red.

 

Connecting your devices 

 

You can use additional Ethernet cables to connect other devices such as laptops or gaming consoles to any of the 4 yellow LAN ports.

fttc3.png

 

Or you can just connect devices via WiFi. You’ll find the WiFi name and password on your modem’s barcode sticker.

tplink_sticker.png

That’s all there is to it! If you have any trouble getting online, reach out on TPG Community or give us a call on 13 14 23 and we’ll be happy to help.

 

jharitos75
Level 4

ks but that is the whole point of my query ..... I have never received below email or SMS... does this mean my NBN service is not activated? If so Why not? 

 

Before you get started, you’ll need 3 things

 

1. A message from us advising you to plug in your NBN FTTC equipment:

 

 

 

 

undefined

david64
Master

The DSL being off means there's still work to be done in the external network. TPG probably arranges to have the equipment delivered before so you will be ready to go when all work is completed.

Might have to wait a bit longer for that message.

RajenS
Moderator

e Hi 5112552

     I can see you are ready to connect, 

     make sure when you connect NCD, no telephones or modems and filters attached to any sockets apart from NCD. 

    

   I will escalate this issue to the case engineer. Someone will get back to you soon. 

 

jharitos75
Level 4

Thanks, please let me know ASAP.